10.12.4 E3 1230v3 RX480 HD5450 驱动成功！
Graphics device = IGPU (not PEG!)VT-d = Off
Windows 7 installation mode = Off
Serial port (Super I/O) = Off
EFI Boot = On
Secure Boot = Off (if it exists)
Fast Boot = Off
Set ErP = Enabled
Set XHCI Handoff to Enabled
(optional) Set boot device to the hard drive you're going to use for macOS
SMBIOS :iMac 17,1
In Finder, press Shift+cmd+G and type "/System/Library/Extensions/". Hit Enter to open the Extensions folder. Now copy AMDRadeonX4100.kext to the Desktop or wherever you keep your hackintosh drivers.
Right-click the copy of the .kext and select Show Package Contents, now open Contents and open Info.plist in a text editor of your choice. Find the line just below
<key>IOPCIMatch</key>
and, inside the <string>, add: 0x67DF1002.Save the edited info.plist and drag'n drop the modified AMDRadeonX4100.kext onto Kext Utility.app to install it.
Repeat steps 1-3 with the file AMDRadeon9510Controller.kext!
Open Clover Configurator >
Graphics and set Inject EDID = On,
FB Name = Dayman
Load VBios = Off,
Inject Intel = Off,
Inject ATI = On.
In Acpi, set "Fix Display" On and in Devices, set Fake ID > ATI to 0x67DF1002. In Boot, set darkwake=8, timeout to 2 and enter the name of your macOS boot disk in "Default Boot Volume".
(thanks to user Mork_vom_Ork) Go to Kernel and Kext Patches -> ForceKextsToLoad, add "\System\Library\Extensions\AMDRadeonX4100.kext" and "\System\Library\Extensions\AMD9500Controller.kext".
The following "code" (by user @Mork_vom_Ork) enables all GPU Cores in the RX 4XX cards. By default only half of them would be used. It is kind of a lot to type, so better copy & paste the following directly into the config.plist file after
<key>KextsToPatch</key>
<array>
using a text editor (TextEdit comes preinstalled ;)):
<dict>
<key>Comment</key>
<string>Change_#_of_RX4x0_CUs-(C)_by_okrasit_2016</string>
<key>Disabled</key>
<false/>
<key>Find</key>
<data>SLgCAAAAAQAAAEiJQ1THQ3wIAAAA</data>
<key>Name</key>
<string>AMDRadeonX4100</string>
<key>Replace</key>
<data>SLgEAAAAAQAAAEiJQ1THQ3wSAAAA</data>
</dict>
<dict>
<key>Comment</key>
<string>Remove_CU_limit_of_RX4x0-(C)_by_okrasit_2016</string>
<key>Disabled</key>
<false/>
<key>Find</key>
<data>D0LIiYuAAAAARIizmQAAAESIcyA=</data>
<key>Name</key>
<string>AMDRadeonX4100</string>
<key>Replace</key>
<data>kJCQiYuAAAAARIizmQAAAESIcyA=</data>
</dict>
<dict>
<key>Comment</key>
<string>Change_init_from_BAFFIN_to_ELLESMERE-(C)_by_Fl0r!an_2016</string>
<key>Disabled</key>
<false/>
<key>Find</key>
<data>6EmF/v++SAEAAEyJ9w==</data>
<key>Name</key>
<string>AMDRadeonX4100</string>
<key>Replace</key>
<data>6EbkAAC+SAEAAEyJ9w==</data>
</dict>
<dict>
<key>Comment</key>
<string>PP_DisablePowerContainment=1</string>
<key>Disabled</key>
<false/>
<key>InfoPlistPatch</key>
<true/>
<key>Name</key>
<string>AMD9510Controller</string>
<key>Find</key>
<data>PGtleT5QUF9EaXNhYmxlUG93ZXJDb250YWlubWVudDwva2V5PjxpbnRlZ2VyPjA8L2ludGVnZXI+</data>
<key>Replace</key>
<data>PGtleT5QUF9EaXNhYmxlUG93ZXJDb250YWlubWVudDwva2V5PjxpbnRlZ2VyPjE8L2ludGVnZXI+</data>
</dict>
SAVE and open the config.plist in Clover Configurator, go to Kernel and Kext Patches section to double-check the new patches are listed!
Shut down your computer and unplug the power!
Install RX 480 into the first slot on the motherboard.
Power computer on and go to BIOS to make sure the graphics adapter is still set to iGPU, not PEG. This seems contradictory but is very important!
Power off, remove display cable from the motherboard and attach it to the RX 480!
Turn the computer back on & wait for the system to boot. No signal is fed to the display until the login screen appears. You should hear the RX 480's fan make a hiss as it enables 20x warp mode full acceleration.
If you want the System Information & "About this Mac…" windows to show the RX 480 name, follow the instructions over at a blog of a legit Apple user. :headbang:
https://www.tonymacx86.com/threads/guide-amd-rx-480-8-gb-msi-h110m-gaming-skylake-i5-6500-macos-10-12-3.209909/
以上是修改方法
35买的 hd5450 设置bios 先启动 hd5450. 就能进系统了
AMD9510Controller.kext，AMDRadeonX4100.kext，config.plist
O(∩_∩)O谢谢楼主 分享 本帖最后由 ostrich130 于 2017-4-25 08:57 编辑
补充一下。10.12.4 得修改 AMD9510Controller.kext10.12.3是 AMD9500Controller.kext
大神。能不能帮我做一个clover config lzyys 发表于 2017-4-25 08:55 https://www.pcbeta.com/static/image/common/back.gif
大神。能不能帮我做一个clover config
参考我的啊。我也不懂 一点一点试出来的。。。 感谢楼主修改的驱动啦！ 我和你一样的配置，看到希望了，我也正好准备买个亮机卡试试 你好，我的亮机卡为hd5770 请问你的显示器连接在 hd5450上面还是rx480上面呢？
大哥，能详细解释下你的插卡状态和显示器连接状态吗 学习了，谢谢 hd7770能用吗主板是msi z87 g43 gaming u和你一样 eemin 发表于 2017-7-12 13:52 https://www.pcbeta.com/static/image/common/back.gif
大哥，能详细解释下你的插卡状态和显示器连接状态吗
我是2个显示器都链接了 直到登陆界面都是 亮机卡 显示 480链接的显示器黑屏
进系统把显示设置 把 下面的应用栏拖到480显示器上
480 插PCIE-1
5450插 PCIE-2 BIOS设置 优先 PCIE2 LeoMacX 发表于 2017-7-13 16:35 https://www.pcbeta.com/static/image/common/back.gif
hd7770能用吗主板是msi z87 g43 gaming u和你一样
亮机卡 随便 有没有驱动无所谓 能进系统就行 ostrich130 发表于 2017-7-16 20:47 https://www.pcbeta.com/static/image/common/back.gif
亮机卡 随便 有没有驱动无所谓 能进系统就行
970能当亮机卡用吗
xf3030 发表于 2017-7-18 01:46
970能当亮机卡用吗
亮机卡的目的引导进系统，然后废弃不用，970做亮机卡，也太土豪了吧 maojinbing 发表于 2017-7-18 07:39 https://www.pcbeta.com/static/image/common/back.gif
亮机卡的目的引导进系统，然后废弃不用，970做亮机卡，也太土豪了吧
哈哈哈，正好有一块儿二手的 这不。。。
感谢分享，楼主辛苦了 还能下载吗？
页:
[1]