【已解决】求一份10.14可用的ALC269文件
本帖最后由 云月天霜霰 于 2018-11-20 16:08 编辑注入ID仍旧为29，麦克风和外放都可用，如何在您的设备上没用请尝试33
注意更新AppleALC到1.3.4版本
上传附件为AppleALC1.3.4
以下内容作废
论坛里的都试验了，就是驱动不了，在10.13.6版本注入ID是29，40
在10.14.1版本把所有的ID我都试验了，几十个，没有一个管用。求助，谁能教教我怎么做，感激不尽
顶顶，电脑是机械革命Z2 电竞豪华版，目前就是声卡和触摸板没驱动，其他的都没问题，求助大佬 我升上去只能用万能驱动，论坛的声卡教程太复杂了，那个关键路径图都不知道怎么生成的，我跟你配置差不多 Codec: Realtek ALC269VC
Address: 0
AFG Function Id: 0x1 (unsol 1)
Vendor Id: 0x10ec0269
Subsystem Id: 0x1d051053
Revision Id: 0x100203
No Modem Function Group found
Default PCM:
rates : 32000 44100 48000 88200 96000 192000
bits : 16 20 24
formats : PCM
Default Amp-In caps: N/A
Default Amp-Out caps: N/A
State of AFG node 0x01:
Power states:D0 D1 D2 D3 CLKSTOP EPSS
Power: setting=D0, actual=D0
GPIO: io=2, o=0, i=0, unsolicited=1, wake=0
IO: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0
IO: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0
Node 0x02 wcaps 0x41d: Stereo Amp-Out
Control: name="Headphone Playback Volume", index=0, device=0
ControlAmp: chs=3, dir=Out, idx=0, ofs=0
Device: name="ALC269VC Analog", type="Audio", device=0
Amp-Out caps: ofs=0x57, nsteps=0x57, stepsize=0x02, mute=0
Amp-Out vals:
Converter: stream=1, channel=0
PCM:
rates : 44100 48000 96000 192000
bits : 16 20 24
formats : PCM
Power states:D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x03 wcaps 0x41d: Stereo Amp-Out
Control: name="Speaker Playback Volume", index=0, device=0
ControlAmp: chs=3, dir=Out, idx=0, ofs=0
Amp-Out caps: ofs=0x57, nsteps=0x57, stepsize=0x02, mute=0
Amp-Out vals:
Converter: stream=1, channel=0
PCM:
rates : 44100 48000 96000 192000
bits : 16 20 24
formats : PCM
Power states:D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x04 wcaps 0xf00000: Mono
Node 0x05 wcaps 0xf00000: Mono
Node 0x06 wcaps 0x611: Stereo Digital
Converter: stream=0, channel=0
Digital:
Digital category: 0x0
IEC Coding Type: 0x0
PCM:
rates : 32000 44100 48000 88200 96000 192000
bits : 16 20 24
formats : PCM
Power states:D0 D1 D2 D3 EPSS
Power: setting=D3, actual=D3
Node 0x07 wcaps 0xf00000: Mono
Node 0x08 wcaps 0x10051b: Stereo Amp-In
Amp-In caps: ofs=0x17, nsteps=0x3f, stepsize=0x02, mute=1
Amp-In vals:
Converter: stream=0, channel=0
SDI-Select: 0
PCM:
rates : 44100 48000 96000 192000
bits : 16 20 24
formats : PCM
Power states:D0 D1 D2 D3 EPSS
Power: setting=D3, actual=D3
Connection: 1
0x23
Node 0x09 wcaps 0x10051b: Stereo Amp-In
Control: name="Capture Volume", index=0, device=0
ControlAmp: chs=3, dir=In, idx=0, ofs=0
Control: name="Capture Switch", index=0, device=0
ControlAmp: chs=3, dir=In, idx=0, ofs=0
Device: name="ALC269VC Analog", type="Audio", device=0
Amp-In caps: ofs=0x17, nsteps=0x3f, stepsize=0x02, mute=1
Amp-In vals:
Converter: stream=1, channel=0
SDI-Select: 0
PCM:
rates : 44100 48000 96000 192000
bits : 16 20 24
formats : PCM
Power states:D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Connection: 1
0x22
Node 0x0a wcaps 0xf00000: Mono
Node 0x0b wcaps 0x20010b: Stereo Amp-In
Control: name="Mic Playback Volume", index=0, device=0
ControlAmp: chs=3, dir=In, idx=0, ofs=0
Control: name="Mic Playback Switch", index=0, device=0
ControlAmp: chs=3, dir=In, idx=0, ofs=0
Control: name="Beep Playback Volume", index=0, device=0
ControlAmp: chs=3, dir=In, idx=4, ofs=0
Control: name="Beep Playback Switch", index=0, device=0
ControlAmp: chs=3, dir=In, idx=4, ofs=0
Amp-In caps: ofs=0x17, nsteps=0x1f, stepsize=0x05, mute=1
Amp-In vals:
Connection: 5
0x18 0x19 0x1a 0x1b 0x1d
Node 0x0c wcaps 0x20010b: Stereo Amp-In
Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-In vals:
Connection: 2
0x02 0x0b
Node 0x0d wcaps 0x20010b: Stereo Amp-In
Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-In vals:
Connection: 2
0x03 0x0b
Node 0x0e wcaps 0xf00000: Mono
Node 0x0f wcaps 0x20010a: Mono Amp-In
Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-In vals:
Connection: 2
0x02 0x0b
Node 0x10 wcaps 0xf00000: Mono
Node 0x11 wcaps 0xf00000: Mono
Node 0x12 wcaps 0x40040b: Stereo Amp-In
Control: name="Internal Mic Boost Volume", index=0, device=0
ControlAmp: chs=3, dir=In, idx=0, ofs=0
Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0
Amp-In vals:
Pincap 0x00000020: IN
Pin Default 0x90a60130: Mic at Int N/A
Conn = Digital, Color = Unknown
DefAssociation = 0x3, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x20: IN
Power states:D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x13 wcaps 0xf00000: Mono
Node 0x14 wcaps 0x40058d: Stereo Amp-Out
Control: name="Speaker Playback Switch", index=0, device=0
ControlAmp: chs=3, dir=Out, idx=0, ofs=0
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals:
Pincap 0x00010014: OUT EAPD Detect
EAPD 0x2: EAPD
Pin Default 0x90170110: Speaker at Int N/A
Conn = Analog, Color = Unknown
DefAssociation = 0x1, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x40: OUT
Unsolicited: tag=00, enabled=0
Power states:D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Connection: 2
0x0c 0x0d*
Node 0x15 wcaps 0x40058d: Stereo Amp-Out
Control: name="Headphone Playback Switch", index=0, device=0
ControlAmp: chs=3, dir=Out, idx=0, ofs=0
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals:
Pincap 0x0001001c: OUT HP EAPD Detect
EAPD 0x2: EAPD
Pin Default 0x01211020: HP Out at Ext Rear
Conn = 1/8, Color = Black
DefAssociation = 0x2, Sequence = 0x0
Pin-ctls: 0xc0: OUT HP
Unsolicited: tag=01, enabled=1
Power states:D0 D1 D2 D3 EPSS
Power: setting=D3, actual=D3
Connection: 2
0x0c* 0x0d
Node 0x16 wcaps 0xf00000: Mono
Node 0x17 wcaps 0x40050c: Mono Amp-Out
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals:
Pincap 0x00000010: OUT
Pin Default 0x40000000: Line Out at Ext N/A
Conn = Unknown, Color = Unknown
DefAssociation = 0x0, Sequence = 0x0
Pin-ctls: 0x00:
Power states:D0 D1 D2 D3 EPSS
Power: setting=D3, actual=D3
Connection: 1
0x0f
Node 0x18 wcaps 0x40058f: Stereo Amp-In Amp-Out
Control: name="Mic Boost Volume", index=0, device=0
ControlAmp: chs=3, dir=In, idx=0, ofs=0
Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0
Amp-In vals:
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals:
Pincap 0x00003734: IN OUT Detect
Vref caps: HIZ 50 GRD 80 100
Pin Default 0x01a11040: Mic at Ext Rear
Conn = 1/8, Color = Black
DefAssociation = 0x4, Sequence = 0x0
Pin-ctls: 0x24: IN VREF_80
Unsolicited: tag=02, enabled=1
Power states:D0 D1 D2 D3 EPSS
Power: setting=D3, actual=D3
Connection: 2
0x0c* 0x0d
Node 0x19 wcaps 0x40058f: Stereo Amp-In Amp-Out
Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0
Amp-In vals:
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals:
Pincap 0x00003734: IN OUT Detect
Vref caps: HIZ 50 GRD 80 100
Pin Default 0x411111f0: Speaker at Ext Rear
Conn = 1/8, Color = Black
DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x20: IN VREF_HIZ
Unsolicited: tag=00, enabled=0
Power states:D0 D1 D2 D3 EPSS
Power: setting=D3, actual=D3
Connection: 2
0x0c* 0x0d
Node 0x1a wcaps 0x40058f: Stereo Amp-In Amp-Out
Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0
Amp-In vals:
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals:
Pincap 0x0000373c: IN OUT HP Detect
Vref caps: HIZ 50 GRD 80 100
Pin Default 0x411111f1: Speaker at Ext Rear
Conn = 1/8, Color = Black
DefAssociation = 0xf, Sequence = 0x1
Misc = NO_PRESENCE
Pin-ctls: 0x20: IN VREF_HIZ
Unsolicited: tag=00, enabled=0
Power states:D0 D1 D2 D3 EPSS
Power: setting=D3, actual=D3
Connection: 2
0x0c* 0x0d
Node 0x1b wcaps 0x40058f: Stereo Amp-In Amp-Out
Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0
Amp-In vals:
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals:
Pincap 0x00003734: IN OUT Detect
Vref caps: HIZ 50 GRD 80 100
Pin Default 0x411111f0: Speaker at Ext Rear
Conn = 1/8, Color = Black
DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x20: IN VREF_HIZ
Unsolicited: tag=00, enabled=0
Power states:D0 D1 D2 D3 EPSS
Power: setting=D3, actual=D3
Connection: 2
0x0c* 0x0d
Node 0x1c wcaps 0xf00000: Mono
Node 0x1d wcaps 0x400400: Mono
Pincap 0x00000020: IN
Pin Default 0x40f38205: Other at Ext N/A
Conn = ATAPI, Color = Purple
DefAssociation = 0x0, Sequence = 0x5
Pin-ctls: 0x20: IN
Power states:D0 D1 D2 D3 EPSS
Power: setting=D3, actual=D3
Node 0x1e wcaps 0x400781: Stereo Digital
Pincap 0x00000014: OUT Detect
Pin Default 0x411111f0: Speaker at Ext Rear
Conn = 1/8, Color = Black
DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x40: OUT
Unsolicited: tag=00, enabled=0
Power states:D0 D1 D2 D3 EPSS
Power: setting=D3, actual=D3
Connection: 1
0x06
Node 0x1f wcaps 0xf00000: Mono
Node 0x20 wcaps 0xf00040: Mono
Processing caps: benign=0, ncoeff=37
Node 0x21 wcaps 0xf00000: Mono
Node 0x22 wcaps 0x20010b: Stereo Amp-In
Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-In vals:
Connection: 7
0x18 0x19 0x1a 0x1b 0x1d 0x0b 0x12
Node 0x23 wcaps 0x20010b: Stereo Amp-In
Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-In vals:
Connection: 6
0x18 0x19 0x1a 0x1b 0x1d 0x0b
我的寨板也一直没驱得动。269VC。原来10.12的时候是voodoo整的，现在10.14等空了再慢慢研究下仿冒吧……269就是id太多了，好几十个。 我的269注入的ID是28 楼主为何不试试applealc USB 声卡 5元那种，随便升级 很好弄吧！ ysx25261465 发表于 2018-11-20 08:45 https://www.pcbeta.com/static/image/common/back.gif
楼主为何不试试applealc
我用的就是appleALC，但是在10.14失效了 小小小毛 发表于 2018-11-20 10:13 https://www.pcbeta.com/static/image/common/back.gif
很好弄吧！
基本上所有ID都实验了，还是驱动不了 962007201 发表于 2018-11-20 09:22 https://www.pcbeta.com/static/image/common/back.gif
USB 声卡 5元那种，随便升级
电脑Usb接口太少了，不太方便 angodson 发表于 2018-11-20 08:12 https://www.pcbeta.com/static/image/common/back.gif
我的269注入的ID是28
我之前一直是29，40，现在把其他ID也都试验了，还是不行 tyuan1231 发表于 2018-11-20 08:07 https://www.pcbeta.com/static/image/common/back.gif
我的寨板也一直没驱得动。269VC。原来10.12的时候是voodoo整的，现在10.14等空了再慢慢研究下仿冒吧……269 ...
万能声卡在用boom时杂音太大了 手动顶帖，求大佬帮助 云月天霜霰 发表于 2018-11-20 10:59 https://www.pcbeta.com/static/image/common/back.gif
我之前一直是29，40，现在把其他ID也都试验了，还是不行
楼主和我差不多，我10.13.6的时候也是注入29，结果升级到10.14.1就不行了，后来把全部ID放入找到个33可以驱动，但是麦克风不行了！刚开始也不行的后来注入33后修复了权限才驱动！ LIAOHONGFEI 发表于 2018-11-20 13:28
楼主和我差不多，我10.13.6的时候也是注入29，结果升级到10.14.1就不行了，后来把全部ID放入找到个33可以 ...
我试过了，注入33也不行，你的驱动能借我用下吗，谢谢 https://github.com/acidanthera/AppleALC/tree/master/Resources/ALC269
试试30 本帖最后由 limumu1997 于 2018-11-20 14:32 编辑
貌似把13.6的AppleHDA换到14就可以了 limumu1997 发表于 2018-11-20 14:22 https://www.pcbeta.com/static/image/common/back.gif
貌似把13.6的AppleHDA换到14就可以了
试过了，不行，改成注入ID33,外放终于能用了